Epson stylus photo 2100 инструкция

Downloads

Краткое содержание страницы № 1

Краткое содержание страницы № 2

Injector Set & Tubes Bottle Holder Tray Special Chip Block (Wrapped in Protective Packaging) 7 Empty 100ml Bottles Special Foam Block that may not be required Bottle Caps & 7 Tube Clamps Clear Piping 10ml Syringe Tube Clip with Adhesive Pad Pair of Latex Gloves ____________________________________________________________________________________________ Check Printer Cond

Краткое содержание страницы № 3

If you have a brand new printer, follow the Epson instructions for setting up your printer. Use the Epson injectors that came with the printer. Follow normal installation instructions for the software. Test the printer by printing pictures. Learn how to use the Epson utilities to run a Nozzle pattern check and to run a Cleaning Cycle. Make sure that the printer can produce a perfect nozzle pattern before proceeding with Eco-Flo installation. If you have been using the printer

Краткое содержание страницы № 4

Fig.2 Step 3 Bottle Preparation Locate the coloured bottle caps and straight lengths of plastic tubes. Insert the straight tube firmly into the bottom of each bottle cap see Fig.3 Fig.3 Step 4 Tube Preparation 4

Краткое содержание страницы № 5

Using a pair of scissors separate all tubes by snipping gently at the tube ends. Please see Fig.4 to the left. Fig.4 Strip back all the tubes by approx 150mm. Please note when assembling the tubes to the bottle caps you may need to strip back more of the tubing in order for the bottles to be seated correctly within the bottle tray. Fig.5 Fig.6 showing tubes pped back stri Step 5 Preparation of The Clamps

Краткое содержание страницы № 6

UB LC C LK Y LM M 2100 Setup Step 7 Assembling the Tubing to the Bottle Caps When you have completed the above process insert the correct tube to the correct ink bottles. PLEASE TAKE CARE when doing this as if this is connected incorrectly there is no turning back see Fig.9 & Fig.10 Fig.9 Fig.10 Wing Adaptor Step 8 Priming the Ink Through the Injectors Shown You ar

Краткое содержание страницы № 7

This process is carried out by inserting the 10ml syringe and wing adaptor at the base of the injector. PLEASE ENSURE THAT THE WING ADAPTOR (TIP ONLY) IS GENTLY INSERTED INTO THE BASE OF THE INJECTOR, DO NOT push the tip any further than 3mm (see diagram opposite) otherwise this will split the base of the injector. Diagram showing the wing adaptor tip PLEASE ENSURE that you DOUBLE CHECK that the correct tube is only inserted gently located to the correct ink bottle be

Краткое содержание страницы № 8

Carefully align them, and when you are happy the injectors are in position. PLEASE BE CAREFUL NOT TO PUSH TOO HARD, AS THIS WILL CAUSE DAMAGE TO THE INJECTOR & PRINTER HEAD. Push the injectors home until you feel a positive seated position see Fig.15 below. Fig.14 Fig. 15 Picture shows injectors fully installed in a 2100 Step 10 Positioning The Foam Block You will need to move the printer head towards the right of the printer in order

Краткое содержание страницы № 9

Fig.17 Fig.18 Next, you will notice that the Tube Support Bracket has both the Hook and Loop Velcro on it. The Hook portion of the Velcro is going to end up attached to your printer. The Loop portion will remain on the Tube Support Bracket. Do not separate the Hook and Loop. Use an alcohol or cleaning solution and clean the top of the printer housing where the Black Tube Support Bracket is going to be attached. Then make sure the area is dry bef

Краткое содержание страницы № 10

This can be done manually by moving the head to the left and right and checking that there is just enough tubing to allow the print head to move freely, without it dragging against any part of the printer see Fig. 20 & Fig. 21 below. The tubing should look and be assembled as the diagrams opposite. Fig.20 Fig.21 PLEASE NOTE, due to the nature of the tubing you may need to leave the head unit in the left hand position as illustrated in Fig.20 left

Краткое содержание страницы № 11

The printer should come on and the head should move back and forth a few times and do a cleaning cycle. When it stops moving, only the green light should be on. A red light at this point indicates that one of the chips has not been recognized. If this is the case please LOCK all tubes with the white clamps and very carefully remove the Injectors, Foam Block and Special Chip Block, Now very carefully check the chip that is not registering. It is advisable to clean the chip by wiping the

Краткое содержание страницы № 12

1 ECO-FLO INSTALLATION INSTRUCTIONS FOR ALL TYPES OF PRINTERS AND SYSTEMS 2 TROUBLE SHOOTING GUIDE 3 INK PURGE TEST FILES AND TONE CHARTS 4 ICC PROFILES FOR USE WITH PERMAJET COLOUR INK AND PAPER COMBINATIONS 5 CURVES FOR USE WITH MONOCHROMEPRO INK SYSTEM. IN ORDER TO USE THE PERMAJET INK SYSTEM TO ITS FULL POTENTIAL, YOU SHOULD NOW TAKE THE TIME TO OPEN THE ENCLOSED CD AND PROCEED TO READ THE FULL SECTION ON PROFILES AND THE “HOW TO INSTALL AND USE ICC PROFILES” DOCUME

Краткое содержание страницы № 13

• It is advised to gently shake by rotation each ink bottle on a regular weekly basis. This is to ensure the pigments stay suspended in solution and gives constant results. • After printing, ink in the tubes should be close to the injectors. The next morning, the ink may have retracted a little this is absolutely normal. When you start to print again the ink will be drawn into the injectors and it will function normally. The system is designed to have some air at the top of the injecto

Download Epson Stylus Photo 2100/2200. Service Manual

Все материалы на сайте представлены исключительно для ознакомления. Все торговые марки и права на публикуемые материалы принадлежат их владельцам.

All materials on the site are presented solely for information. All trademarks and copyrights in the published materials belong to their respective owners.

Setting Up the Printer Hardware

1. Unpack 2. Remove protective materials 3. Attach the printer parts

c

Caution:

If the printer comes on when you plug in the power cord, turn off the

printer by pressing down the P power button until the printer lights

go out.

4. Connect the printer

Connect the printer cable to the ports on the computer and the printer.

The contents may vary in

certain locations.

Power cord may

come attached in

some countries.

Setup

Be careful not to throw out the

8 cm CD-R support and the

CD-R print position check disk

paper support

ink cartridges

printer

photo catcher

printer software &

online guide CD-ROM

roll paper holder

automatic roll

paper cutter

cleaning kit

CD-R print position

check disk

8 cm CD-R

support

CD-R tray

IEEE 1394

Parallel

USB

Print quality is determined by the driver settings and the paper. See the online Reference Guide for details on driver settings and available media. Also visit the EPSON Web Site for the latest information.

Setup

Read the Safety Instructions on the back of this sheet when setting up and using this printer.

English

Color Ink Jet Printer

c

Cautions must be observed to

avoid damage to your

equipment.

Notes contain important information

and useful tips on the operation of your

printer.

Cautions and Notes

Installing the Printer Software and the Ink Cartridges

For Windows

1. Make sure that printer is off.

2. Insert the printer software CD in the

CD-ROM drive. If the Installer dialog

box does not appear, double-click

SETUP.EXE in the CD-ROM.

3. Select Install Software, and click .

4. Follow the on-screen instructions.

Note:

❏ Remove the protective material under the

cartridge cover before installing ink

cartridges.

❏ If the Setup utility does not start, press the

P power button on the printer and follow

the instructions in the Macintosh section of

this sheet, beginning from “ 3. Install the

ink cartridges.”

When ink cartridge installation is complete, proceed to “Load paper and

check the print head nozzles” on this sheet.

For Macintosh

1. Install the printer software

c

Caution:

Turn off all virus protection programs before you install the printer

software.

1. Make sure that printer is off, then turn on your Macintosh and insert the

printer software CD in the CD-ROM drive.

2. Double-click the EPSON icon.

3. Select Install Software, and click .

4. Follow the on-screen instructions.

2. Select the printer

After you have installed the printer software, you need to select your printer.

1. Press the P power button to turn on the printer. The print head moves

to the ink cartridge installation position.

2. Choose Chooser from the Apple

menu. Then, select the icon for

your printer and the port that your

printer is connected to.

3. Close the Chooser.

3. Install the ink cartridges

1. Lower the output tray, then open the

printer cover and the cartridge

cover.

c

Caution:

Do not move the print head by

hand, as this may damage the

printer.

Note:

For best results, shake the ink

cartridge four or five times before

opening the package.

2. Remove the protective material under the

cartridge cover before installing ink

cartridges.

3. Remove the new ink cartridges from their protective bag.

c

Caution:

❏ Be careful not to break the hook on the side of the cartridge

when you remove it from the protective bag.

❏ Do not shake the ink cartridge after removing from the bag;

this can cause leakage.

❏ Do not remove or tear the label on the cartridge; this can

cause leakage.

❏ Do not touch the green IC chip on the side of the cartridge.

Doing so may prevent normal operation and printing.

4. Place the ink cartridges vertically into the cartridge holders. Without

applying excessive force, push the ink cartridges down until they click

into place. To place them vertically, install the ink cartridges from one

end.

Note:

Install all ink cartridges. The printer will not work unless all cartridges

are installed properly.

5. Close the cartridge cover and the printer cover.

6. Press the

H ink button. The printer moves the print head and begins

charging the ink delivery system. This process takes about one and a

half minutes. While charging, the P power light and the ink lights flash

and the printer produces a variety of mechanical sounds. This is normal.

c

Caution:

❏ Do not turn the power off during the ink charging process.

❏ Do not load paper until ink charging is complete.

Note:

If the ink end error occurs after the print head moves to its home position,

the ink cartridge may not be installed properly. Press the H ink button

again, and reinstall the ink cartridge until it clicks into place.

When the ink charging process is finished, the P power light stops flashing

and remains on.

The ink cartridges packaged with your printer are partly used during initial

setup. In order to produce high quality printouts, the print head in your printer

will be fully charged with ink. This one-off process consumes a quantity of

ink and subsequent cartridge sets will last for their full rated life.

Make sure that the computer is turned on. Load paper into the sheet feeder

making sure that the side of the paper that you wish to print onto is facing

up and that the right edge of the paper is against the right edge guide. Next,

slide the left edge guide so that it is against the left edge of the paper.

Once paper is loaded, follow these steps to check the print head nozzles.

For Windows users

1. Click the Start button, point to Settings, and

click Printers.

2. For Windows Me, 98, and 95 users, select

your printer, then click Properties on the File

menu. Then click Utility tab.

For Windows XP and 2000 users, select your

printer, then click Printing Preferences on

the File menu. Then click Utility tab.

For Windows NT 4.0 users, select your

printer, then click Document Defaults on

the File menu. Then click Utility tab.

3. Click the Nozzle Check button, and follow

the on-screen instructions.

4. When you are finished, click OK to close the Properties dialog box.

Your printer is now set up and ready to use.

For Macintosh users

1. Select Page Setup in the Finder’s File menu.

2.

Click the utility icon.

3. Click the Nozzle Check button, and

follow the on-screen instructions.

4. When you are finished, click OK to

close the utility dialog box. Then click

OK to close the Page Setup dialog

box.

Your printer is now set up and ready to

use.

Do not touch this part.

printable side up

left edge guide

output tray extension

4021354-00

xxx

Load paper and check

the print head nozzles

Recommended Documentation: