Futaba r7008sb инструкция на русском

1M23N17491

R7008SB

Instruction Manual

FASSTest-2.4GHz Bidirectional

Communication System

S.BUS2 / S.BUS Port and 8 Channels for

Conventional System Receiver

Usage precaution

• Analog servos cannot be used with the

R7008SB in the FASSTest 12CH mode.

• The R7008SB receiver can only be used

with FASSTest capable transmitters.

• Don’t connect to Extra Voltage before turn-

ing on a receiver.

WARNING

Changes or modification not expressly

approved by the party responsible for

compliance could void the user’s authority

to operate the equipment.

The R7008SB receiver should be protect-

ed from vibration by foam rubber, Velcro

or similar mounting methods. Protect

from moisture.

Keep away from conductive materials to

avoid short circuits.

Antenna installation precaution

Do not cut or bundle the receiver antenna

wire.

Do not bend the coaxial cable. It causes

damage.

The antennas must be mounted in such a

way to assure they are strain relieved.

Compliance Information Statement (for U.S.A.)

This device, trade name Futaba Corporation of America, model number R7008SB, complies with part15 of the

FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

(3) This module meets the requirements for a mobile device that may be used at separation distances of more than

20cm from human body.

To meet the RF exposure requirements of the FCC this device shall not be co-located with another transmitting

device.

The responsible party of this device compliance is: Futaba Service Center 3002 N Apollo Drive Suite 1,

Champaign, IL 61822 U.S.A. TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support)

Thank you for purchasing a Futaba R7008SB FASSTest-

2.4GHz compatible receiver. The R7008SB receiver features bi-

directional communication with a FASSTest Futaba transmitter

using the S.BUS2 port. Using the S.BUS2 port an impressive

array of telemetry sensors may be utilized. It also includes both

standard PWM output ports and S.BUS output ports.

Applicable systems: Futaba FASSTest-2.4GHz

system transmitter

Keep the antenna as far away from the motor,

ESC and other noise sources as you possibly can.

Be sure that the two antennas are placed at 90

degrees to each other.

• The R7008SB has two antennas. In order to maximize signal

reception and promote safe modeling Futaba has adopted a

diversity antenna system. This allows the receiver to obtain

RF signals on both antennas and fly problem-free.

Antenna installation for carbon fuselage

WARNING

You must leave 30mm at the tip of the antenna

fully exposed. The exposed antenna should be

secured so that it cannot move around or back

inside of your aircraft.

S.BUS2 precaution

DANGER

DANGER

Don’t connect a connec-

tor, as shown in a before

figure.

• It will short-circuit, if it connected

in this way. A short circuit across

the battery terminals may cause

Do not insert either a switch

or battery in this manner.

abnormal heating, fire and burns.

WARNING

Only S.BUS2 capable devices may be connected

to the S.BUS2 port. Standard S.BUS servos and

gyros should not be connected to the S.BUS2 port.

R7008SB Specifications

FASSTest-2.4GHz system(18CH/12CH mode)/

S.BUS2 and S.BUS port and 8 channels for conven-

tional system receiver

• Dual antenna diversity

• Size: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3 mm)

• Weight: 0.38 oz. (10.9g)

• Power requirement: 3.7V to 7.4V(Voltage range: 3.5 to

8.4V)

• Battery F/S Voltage: It sets up with a transmitter

• Extra Voltage port: 0 ∼ 70V DC

* Be sure that when using ESCs regulated output the capacity of the

ESC must meet your usage condition.

It connects with the

＋

battery for power, etc.

External voltage input

cable of an option is

−

used. The voltage of

the battery can be

displayed with a

transmitter.

S.BUS2

(Antenna installation)

90˚

(Typical installation)

Please refer the table below for

LED status vs receiver’s condition.

LED Indication

Green

Red

Status

Off

Solid

No signal reception

Solid

Off

Receiving signals

Alternate blink

Unrecoverable error (EEPROM, etc.)

Приемник Futaba R7008SB 2.4 Ггц, протокол FASSTest® (с телеметрией)

Компактный, легкий R7008SB 2,4 ГГц FASSTest® приемник со встроенным передатчиком  для телеметрии.
Несмотря на свои небольшие размеры всего 47,3 х 24,9 х 14,3 мм и вес всего 13 г приемник R7008SB является мульти функциональным устройством. А это  еще — встроенный передатчик телеметрии — может отправлять до 32 наборов данных на землю (дальность до 1000 м).

Естественно, приемник оснащен 8 выходами для подключения в них обычных сервомашинок (PWM). 

Диапазон каналов можно переключать, т.е использовать либо с 1 по 8, либо с 9 по 16. Например, ставятся 2 приемника R7008SB в параллель для получения 16 обычных каналов (PWM). 

Порт для шины S-BUS: и в этом случае могут быть подключено по ней до 18 S-Bus/S-Bus2 сервоприводов или др.устройств.Датчики телеметрии могут быть подключены и через разъем S.BUS2, и до 32 телеметрических данных могут быть переданы. 

Если использовать два приемника, число телеметрических каналов возрастает до 64!

Встроенный  передатчик  телеметрии приемника посылает данные с  S.BUS2 разъема на  FASSTest ® передатчик (T-18MZ), где данные отображаются на экране или преобразуются в звуковую (голосовую) форму. Если подключен модуль Wi-Fi (Wi—Fi Rx—Box 2,4 GHz FASSTest®), то телеметрические данные также могут быть отправлены по радио на смарт-фоны (Android, Apple), нетбук, ноутбук и т.д., и на любые мониторы, подключенные к этим устройствам.

Когда приемник подключен, данные, такие как: напряжение на батареи приемника, внешнее напряжение (до 70 В постоянного тока), мощность сигнала (?),т.е. необходимые данные для передачи, автоматически передаются на землю.

Приемник  Futaba R7008SB работает только по протоколу FASSTest®. (T18MZ,T18SC,T16SC, T14SG ).

Таблица совместимости приемников Futaba 

Link to the transmitter

Easy Link ID allows FASSTest receivers to link to compatible

transmitter without pressing the link button on the receiver.

1

2

linking mode.

3

4

mode.

5

W

solid green, linking is complete.

(

WARNING

transmitter.

FASSTest

FASSTest is a bidirectional communication system between the R7008SB

receiver and FASSTest capable transmitters. Multiple optional telemetry

sensors may be connected to the S.BUS2 on the receiver and that data is

in turn displayed on the transmitter.

What is S.BUS?

Unlike conventional radio control systems, the S.BUS system

uses data communication to transmit control signals from a

receiver to a servo, gyro, or other S.BUS compatible device.

This data includes commands such as «move the channel 3

servo to 15 degrees, move the channel 5 servo to 30 degrees»

[Connection by S.BUS system]

S.BUS

* Can also e sed to ether ith conventional servos Ho ever conventional servos cannot e sed y the S.BUS o tp t

hen sin servos ith a remote attery pac

*

lease refer to the instr ction man al of S.BUS H

WARNING

ince the

servo s itches the operation mode a tomatically accordin to the type of si nal (

inserted or removed hile the po er is

be re-

R7008SB

S.BUS output

Ch output/

Battery terminal

Battery

Conventional

servo

SBC-1

CIU-2

se S.BUS H

ith Ca le (2

ith Ca le (2

ay/remote attery pac

→

an

connected servo ill e erroneo sly reco ni ed and may stop

FUTABA CORPORATION

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan

Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

Channel Modes

The R7008SB is capable of changing its channel allocations as described

in the table below. This is especially important when using the receiver

in a dual receiver mode. See your transmitter operation manual for

complete details on operating in the dual receiver mode.

1

receiver.

2

3

4

5

6

O

solid color.

7

P

R7008SB CH Mode table

Output

connector

1

2

3

4

5

6

7/B

8/SB

Red LED

blink

S.BUS2

S.BUS2 extends S.BUS and supports bidirectional communication.

Sensors are connected to the S.BUS2 port.

port.

to multiple devices. The S.BUS devices execute only those

commands for their own set channel. For this reason, it can

be used by connecting multiple servos to the same signal

line.

2ch

5ch

S.BUS hub

S.BUS hub

S.BUS

1ch

3ch

S.BUS servo

ay/remote attery pac

se)

se) for the connection method

si nal/

Channel

Mode Ａ

Mode B

Mode C

1 ∼ 8CH

1 ∼ 7CH

9 ∼ 16CH

1

1

9

2

2

10

3

3

11

4

4

12

5

5

13

6

6

14

7

7

15

8

S.BUS

16

1 time

2 time

3 time

4ch

18MZ transmitter.

si nal) from the receiver if the connector is

C

Mode D

9 ∼ 15CH

9

10

11

12

13

14

15

S.BUS

4 time

2 11 12 (1)

Accompanying Data:

FUTABA R7008SB Receiver, Transmitter PDF Manual  (Updated: Sunday 25th of June 2023 02:58:52 PM)

Rating: 4.1 (rated by 37 users)

Compatible devices: R304SB, R204GF-E, 9z, 2PKA, 4pls, FX-18, T10PX, R7003SB.

Recommended Documentation:

Text Version of Manual 

(Ocr-Read Summary of Contents of some pages of the FUTABA R7008SB Document (Main Content), UPD: 25 June 2023)

• FUTABA R7008SB User Manual

• FUTABA R7008SB User Guide

• FUTABA R7008SB PDF Manual

• FUTABA R7008SB Owner’s Manuals

Recommended: CHARACTER, 545137281, Xen

Additional Information:

Operating Impressions, Questions and Answers:

Applicable systems: Futaba FASSTest-2.4GHz system transmitter

R7008SB

FASSTest-2.4GHz Bidirectional Communication System

S.BUS2 / S.BUS Port and 8 Channels for Conventional System

Receiver

Compliance Information Statement

(for U.S.A.)

This device, trade name Futaba Corporation of America, model number

R7008SB, complies with part15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference

that may cause undesired operation.

(3) This module meets the requirements for a mobile device that may be used

at separation distances of more than 20cm from human body.

To meet the RF exposure requirements of the FCC this device shall not be co-

located with another transmitting device.

The responsible party of this device compliance is:

Futaba Service Center

3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.

TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support)

R7008SB Specifications

FASSTest-2.4GHz system(18CH/12CH mode)/S.BUS2 and S.BUS port

and 8 channels for conventional system receiver
• Dual antenna diversity

• Size: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3 mm)

• Weight: 0.38 oz. (10.9g)

• Power requirement: 3.7V to 7.4V(Voltage range: 3.5 to 8.4V)

• Battery F/S Voltage: It sets up with a transmitter

• Extra Voltage port: 0 ～ 70V DC

* Be sure that when using ESCs regulated output the capacity of the ESC must

meet your usage condition.

Thank you for purchasing a Futaba R7008SB FASSTest-2.4GHz compatible receiver. The R7008SB receiver features bi-directional communication

with a FASSTest Futaba transmitter using the S.Bus2 port. Using the S.Bus2 port an impressive array of telemetry sensors may be utilized. It also

includes both standard PWM output ports and S.Bus output ports.

LED Indication

Green

Red

Status

Off

Solid

No signal reception

Solid

Off

Receiving signals

Alternate blink

Unrecoverable error (EEPROM, etc.)

(Antenna installation)

90˚

Please refer the table below for LED status vs

receiver’s condition.

1M23N17454

S.BUS2

port

S.BUS port (8/SB）

(S.BUS2）

R7008SB

Terminal box

S.BUS Servo

S.BUS Gyro

HUB

HUB

HUB

HUB

Extra Voltage

Port

Link/Mode switch

Antenna

LED

Servo for conventional

system

Channel1 output
Channel8 output

Temperature

Sensor

RPM

Sensor

Voltage

Sensor

Voltage

Sensor

Altitude

Sensor

Altitude

Sensor

S.BUS2 Tool

Battery to 7/B

(It is not used for a link.)

Usage precaution

• Analog servos cannot be used with the R7008SB in the FASSTest

12CH mode.

• The R7008SB receiver can only be used with FASSTest capable

transmitters.

• Don’t connect to Extra Voltage before turning on a receiver.

WARNING

Changes or modification not expressly approved by the

party responsible for compliance could void the user’s
authority to operate the equipment.

The R7008SB receiver should be protected from vibration

by foam rubber, Velcro or similar mounting methods.

Protect from moisture.

Keep away from conductive materials to avoid short cir-

cuits.

Antenna installation precaution

Do not cut or bundle the receiver antenna wire.

Do not bend the coaxial cable. It causes damage.

The antennas must be mounted in such a way to assure

they are strain relieved.

Keep the antenna as far away from the motor, ESC and

other noise sources as you possibly can.

Be sure that the two antennas are placed at 90 degrees to

each other.

• The R7008SB has two antennas. In order to maximize signal reception

and promote safe modeling Futaba has adopted a diversity antenna

system. This allows the receiver to obtain RF signals on both antennas

and fly problem-free.

Antenna installation for carbon fuselage

WARNING

You must leave 30mm at the tip of the antenna fully ex-

posed. The exposed antenna should be secured so that it

cannot move around or back inside of your aircraft.

(Typical installation)