Инструкция на телефон senao sn 258 plus

Посмотреть все Senao руководства Посмотреть все Senao телефон руководства

SN-258 PLUS

Instruction Manual

Before operating the unit, please read this manual thoroughly, and retain it for future reference.

EN

This product is prohibited to be used without permission from the government authorities in the relevant jurisdictions

Manufactured by

ISO-9001

Certified Facturies

6

7

8

9

10

1

2

3

4

5

11

12

Thank you for purchasing this SN-258 PLUS cordless telephone, one of the high-quality products produced by

SENAO. To obtain optimum performance, please be sure to read this manual carefully before starting operation and keep it for future reference.

Before Initial Use

For the efficient and safe operation of your SN-258 PLUS, please read the page 34~35 before use.

Accessories

Instruction manual

AC adaptor for base unit (DC 12V/ 800mA)

Telephone line

Telescopic antenna for base unit

Battery pack (Ni-Mh 750mAh)

Belt clip

Charger with AC adaptor

Vehicle charger

Ear-microphone

Outdoor antenna with cable for base unit

Car antenna

Travel charger

1 book

1 pc

1 pc

1 pc

1 pc

(optional)

(optional)

(optional)

(optional)

(optional)

(optional)

(Attached with

additional handset)

EN

(1)

SN-258

PLUS

Instruct and reta

Manua instrucc ion Ma in it for fu

the unit l instru ines y c ture refe onserve

, please rence. etenida lo para mente e

futuras is manu al thoro ughly,

EN

ES

RU

This pro used w relevan duct is p ent auth rohibite tions n from

the

the

(2) (3) (4) (5) (6) (optional) (7) (optional)

(12) (Attached with

additional handset)

(8) (optional)

(9) (optional) (10) (optional) (11) (optional)

1-EN

For Best Performance

Battery Charge

To power the handset, install the battery (p.9) and charge it for about 12 hours before initial use (p.10).

CHA

RGE

IN

US e l e s s S o l u t i o n P r o v d e r

// VOL

// VOL

//

H3

RING

INT-C

OM

MEMO

Operating Distance/Noise

Calls are transmitted between the base unit and the handset using wireless radio waves. For maximum distance and noise free operation, the recommended base unit location is:

EN

Away from electronic appliances such as a TV, personal computer, or another cordless phone.

At a HIGH and CENTRAL location with no obstructions such as walls.

Raise the base unit antenna and extend fully both the telescopic antenna of base unit and handset.

KEY LOCK

IN USE BATT.LOW

SCRAMBLER

FLASH

REDIAL MEMO

FUNC

INT

1

4

GHI

7

PQ

R S

2

ABC

5

JKL

8

TUV

0

Oper

3

DEF

6

MNO

9 W X

Y Z

2-EN

Contents

Features . . . . . . . . . . . . . . . . . . . . .5

Location of Controls . . . . . . . . . . . . . . . 6

A. Base Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

B. Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

C. Charger (optional) . . . . . . . . . . . . . . . . . . . . . . .7

Installation . . . . . . . . . . . . . . . . . . . . . 8

EN

A. Base Unit . . . . . . . . . . . . . . . . . . . . . . . . . .8

B. Handset . . . . . . . . . . . . . . . . . . . . . . . . . . 9

C. Twin Charger (Optional) . . . . . . . . . . . . . . . . . . . . .9

D. Charging Battery . . . . . . . . . . . . . . . . . . . . . 10

E. Travel Charger (For Additional Handset) . . . . . . . . . . . .10

F. Ear-microphone (Optional) . . . . . . . . . . . . . . . . .11

Basic Operation. . . . . . . . . . . . . . . . 15

A. Turn On/ Off the Handset . . . . . . . . . . . . . . . 15

C. Redial . . . . . . . . . . . . . . . . . . . . . . . . . 15

E. Answering Calls . . . . . . . . . . . . . . . . . . . . . . 16

F . I ntercom . . . . . . . . . . . . . . . . . . . . . .17

G . In tercom d uring a C all . . . . . . . . . . . . . . . . 18

J. Group Call (Walkie-Talkie Mode) . . . . . . . . . . . 20

3-EN

Advanced Operation. . . . . . . . . . . . . . 23

A. Adjusting Ringer Volume. . . . . . . . . . . . . . . . . 23

B. Adjusting Voice Volume . . . . . . . . . . . . . . . . 24

C. Selecting Voice Mode . . . . . . . . . . . . . . . . . . . . . 25

D. Transferring a Call among Handsets. . . . . . . . . . . . . 25

E. Changing the Channel during a Conversation. . . . . . . .26

F. Display the Battery Status. . . . . . . . . . . . . . . . . . . . . 26

Features Setting. . . . . . . . . . . . . . . . . 27

A. Setting the Base Unit. . . . . . . . . . . . . . . . . . 27

EN

1. Setting Pause duration. . . . . . . . . . . . . . . . . 27

2. Setting Dialling Mode. . . . . . . . . . . . . . . . . . . 27

3. Setting Flash Duration. . . . . . . . . . . . . . . . . . . 27

4. Setting amount of Handsets in the System. . . . . . . . 28

5. Setting Transferring Waiting Time . . . . . . . . . . . . . 28

6. Setting Call-back Waiting Time . . . . . . . . . . . . . . 28

B. Setting the Handset . . . . . . . . . . . . . . . . . . . . . 29

1. Change Handset’s ID . . . . . . . . . . . . . . . . . .29

2. Setting Ring Mode for each Handset . . . . . . . . . . 29

3. Setting Stand-by Time for each Handset . . . . . . . . . 30

Registering Handset for Multi-handset System . .

. . . . . . . . . . . . . . . . . . . . . . . . . . 31

A. Handset Registration . . . . . . . . . . . . . . . . . . . 31

B. De-registering Handset . . . . . . . . . . . . . . . . . . 32

C. Checking the Handset’s IID Number. . . . . . . . . . . . . . 32

Troubleshootings . . . . . . . . . . . . . 33

Specification. . . . . . . . . . . . . . 34

Important Safety Instructions . . . . . . . . . 35

4-EN

Features

*

Multi-channel access with auto-scan.

*

Multi-handset system (up to 15).

* Multi-base system (up to 4).

*

Walkie-talkie between handsets (up to 15 handsets).

*

Half-Duplex group call.

*

Two-way paging and hands-free intercom.

*

10-set memory dial for each handset (20 digits).

*

Last number redial.

*

Tone/Pulse dialling mode selectable.

*

Change channel during conversation.

*

Keypad lock function.

*

Flash time programmable.

*

Ring volume adjustable.

*

Voice volume adjustable.

*

Music on hold.

*

Touch any key answer.

*

Handset with power saving circuit.

*

Low battery alert and indicator.

* Out of range alert.

*

Battery power status display.

* Fast charge.

*

Built-in noise cancellation circuit (Compander).

*

Built-in voice security and mutation circuit (Scrambler).

*

Auto answer and auto hang up.

*

Transferring a call among handsets.

*

Hands-free kit for handset (optional).

*

Separate charger (optional).

* Vibration alert (Vibration version only).

5-EN

EN

A. Base Unit

Location of Controls

Antenna

DC IN jack

TONE/PULSE switch

Line jack

TEL. jack

Speaker

CHA

RGE

POWER

IN

US

E

W i r e l e s s S o l u t i o n P r o v i d e r

H3

RING

OM

MEMO

Microphone

Handset charging slot

H1: Paging handset 1/

voice volume up

H2: Paging handset 2 /

voice volume down

H3: Paging handset 3/

Ringer volume adjustable key

INT-COM: Paging all of the handsets

/ Memo key

CHARGE: CHARGE indicator

POWER: POWER indicator

IN USE: IN USE indicator

6-EN

B. Handset

Car Antenna jack

Receiver

PTT KEY: Lock Keypad

/ Push To Talk

Scan LED array

KEY LOCK

IN USE BATT.LOW

SCRAMBLER

Operation keys

: Talk key/

Flash key

: End key/

Power On/Off

: Intercom key

FLASH

REDIAL MEMO

FUNC

INT

Dialling keys ear-Microphone jack

Microphone

C. Twin Charger (Optional)

1

4

GHI

7

PQ

R S

2

ABC

5

JKL

8

TUV

0

Oper

3

DEF

6

MNO

9 W X

Y Z

Spare battery slot

Antenna

Indicators

KEY LOCK: Lock Keypad

IN USE: In use indicator

BATT. LOW: Low battery

indicator

SCRAMBLER: Scrambler

indicator

Function keys

P/ VOL : Pause/ Ringer

volume/ Speaker

volume key

REDIAL : Last number

redial/ Battery

status display key

MEMO : Memory key

FUNC : Function key

DC IN jack

Spare battery indicator

Power indicator

7-EN

Installation

A. Base Unit

Please set up the base unit according to the following steps (1)~(8).

(1) Install the telescopic antenna of the

base unit and extend it fully and

vertically.

(2) Connect the standard telephone to

the TEL. jack.

(3) During installation, pick up the hand

held of the standard telephone to avoid

electric shock caused by an incoming call.

(1)

(4) Connect the telephone line

to the LINE jack with the

local telephone system.

(8)

(5) Set the dialling mode to

TONE. If you can not dial,

set it to PULSE.

(6) Please use only the SENAO

AC adaptor supplied with

the base unit, and connect the

AC adaptor to the DC IN jack.

(7) The AC adaptor is

set on 220V. If your

power source is 110V,

please switch it to

110V before installing.

(8) Plug the AC adaptor

into power outlet.

(3)

(7)

(6)

110V 220V

(5) (2) (4)

AC adaptor

(Output DC 12V )

8-EN

B. Handset

Take the battery from gift box and clip it into the handset.

(1) (2)

C. Twin Charger (Optional)

(1) Plug the AC adaptor to the DC IN jack.

(2) Plug the AC adaptor into the electric

wall outlet.

(3) The spare battery indicator will

becomes flash while is in charge.

It becomes green while the battery

is fully charged. It takes around 2 hrs.

to fully charge Ni-Mh battery pack.

(3)

Spare battery indicator

Power indicator

Note: Please use only the SENAO AC adaptor supplied with this charger.

9-EN

D. Charging Battery Charge

The handset can be charged on the base unit or the charger.

(1) Place the handset on the base unit with facing up.

The CHARGE indicator will light up.

(2) Place the handset on the charger with standing up.

The scan LED array will run up.

(3) The fast charging will be activated automatically, and the scan

LED array runs fast indicating this operation.

(4) The slow charging automatically starts once the fast charging is

finished. The scan LED array runs slowly for slow charging.

Scan LED array

KEY LOCK

IN USE BATT.LOW

SCRAMBLER

FLASH

REDIAL MEMO

FUNC

INT

1

4

GHI

7

2

ABC

5

JKL

8

TUV

0

Oper

3

DEF

6

MNO

9

H1

VOL

H2

VOL

RING

INT-C

OM

/ MEMO

CHA

RGE

POWER

IN

US

E

W i r e l e s s S o l u t i o n P r o v i d e r

CHARGE indicator

KEY LOCK

IN USE BATT.LOW

SCRAMBLER

FLASH

REDIAL MEMO

FUNC

INT

1

4

GHI

7

PQ

R S

2

ABC

5

JKL

8

TUV

0

Oper

3

DEF

6

MNO

9 W X

Y Z

Scan LED array

E. Travel charger (For Additional Handset)

Plug the charger into a wall socket and insert the plug to the DC IN jack of your handset. The charging times is approximately 5 hours. Check the charging status on the

LED array. The operation of handset could be executed during the charging process.

10-EN

F. Ear-Microphone (Optional)

You can answer and end calls by pressing the button on the microphone part of the ear-microphone. It also could be used as the Walkie-Talkie function. You can press button to talk, then release it to listen.

Answer / End / Push to Talk

Key

Note: To end calls, please keep pressing button for more than 2 sec.

G. Vehicle charger (Optional)

The vehicle charger’s ensures your phone is ready for use wherever you travel. This small charger’s functional design fits most car lights and interiors. The charging time is about 5 hours, and you can use your phone freely during charging. A green light indicates that is ready for charging. Check the charging status on the phone display. The input voltage can be 12 or 24 V DC, negative grounding.

Avoid prolonged charging when the car engine is not running, this may cause the battery of your car to drain. Note also that in some cars the cigarette lighter plug is not provided with electricity if the ignition is switched off. Verify that green LED light is on.

Power indicator

11-EN

H. Outdoor Antenna (Optional)

Installation of the outdoor antenna is very important for communication range and quality. Be sure to follow the following procedures.

1. The tops of the base unit should be

matched with the marks on the

antenna, as illustrated in Figure 1.

NOTE: Use the screw driver to screw

the antenna tight.

2. Lock the 6 ground planes with the

base part as illustrated in Figure 2.

NOTE: Long and short ground planes

should be alternately arranged.

Figure 1

12-EN

Figure 2

3. Assemble cable jack with the base part

as illustrated in Figure 3.

4. Find a pole which is over 5 M long and

22~39 mm in diameter and connect it

with the base tube as indicated in

Figure 4.

NOTE: A bamboo pole is preferred if a

metal one is used, be sure it is

isolated.

5. Put up the pole and make a loop with

the cable cord. The loop which is 15 cm

in diameter is made to prevent water

from going down into the base unit (as

figure 5).

6. The assembled outdoor antenna (as

indicated in Figure 6).

Screw

Washer

Screw

Pole

Cable

Base tube

Cable cord connector

Ground planes

U-bracket

Pole

Figure 3

Washer

Figure 4

U-bracket

Loop

Figure 6

13-EN

Pole

Tape

Figure 5

NOTES

(1) Make sure that the cable is tied to the cable connector in order to

maintain the radio frequency transmission performance.

(2) The ground plane should be at least 3 meters above the ground.

(3) No obstruction can be present within 3 meters from the antenna (as

shown in Fig 7~9).

(4) Straighten the remaining cable.

(5) Bending cable cord will increase loss of transmission power.

(6) Make a loop before pulling the cable into the house. The loop can

prevent rain from going into the house.

(7) The higher the antenna is installed the better the communication will

be.

(8) Keep the antenna and cable from high-voltage sources to avoid

electric shocks. Don’t install the antenna in the rain to avoid

thunder striking.

Over 3 M (correct)

Over 3 M (correct)

Figure 7

Less than 3 M

(incorrect)

Less than 3 M (incorrect)

Over 3 M (correct)

Over 3 M

(correct)

Figure 8

Figure 9

14-EN

Basic Operation

A. Turn On / Off the Handset

1. Turn on the handset

When the handset is power off, press to turn it on. A power on

tone «DO-MI-SO-DO» sounds.

Power off

«DO-MI-SO-DO»

Power on

2. Turn off the handset

When the handset is in stand-by mode, press and hold about 2

seconds until a power off tone «SO-MI-DO» sounds.

» SO-MIDO»

Power on

(stand-by) 2 seconds

Power off

B. Making calls

For example, dial the phone number 22183588

2 2 1 8 3 5 8 8

Phone No.

Press first, then dial the number after hearing the dial tone.

To hang up, press or place the handset on the base unit or on

the charger to hang up the phone.

C. Redial

REDIAL

While in stand-by, press first, then press REDIAL .

During a call, press REDIAL to redial the last number dialled

15-EN

D. Automatic Dialling

1. Storing phone numbers in memory (10 sets of 20-digit number

maximum) (in stand-by mode)

MEMO 2 2 1 8 3 5 8 8 MEMO N ( stand-by)

Phone No. Store Location (N: 0~9)

2. If the base unit is connected to a PBX

We recommend you press P/VOL (PAUSE) between the access

number 0 or 9 for an outside line and the phone number.

MEMO 0 P/VOL 2 2 1 8 3 5 8 8 MEMO N (stand-by)

Access No. PAUSE Phone Number Store

Location

(N:0~9)

Pressing P/VOL (PAUSE) once creates a 6 second pause (P. 27). This

prevents mis-dialling when you redial or dial a stored number.

When finished, a confirmation tone «bi-bi» sounds.

When failed, an error tone «bi-bi-bi» sounds.

If misdialed, press to end storing, then restart.

3. Dialling a stored number

MEMO N (N: 0~9) (stand-by)

Auto dial the phone number stored in location » N «.

Press first, then press MEMO N after hearing the dial tone.

E. Answering Calls

Press (or any key except ) on the handset to answer a call.

If the handset is placed on the base unit or on the charger, pick it up

to answer a call.

To hang up, press or place the handset on the base unit or on

the charger.

16-EN

F. Intercom

1. Paging the base unit from the handset

(1) Handset: Press and the intercom is automatically established.

(2) Base unit: When the other party’s voice is heard, answer through the

microphone.

(3) Handset: To end the intercom, press or place the handset on

the base unit or on the charger.

2. Paging all the handsets from the base unit

(1) Base unit: While in stand-by press INT-COM and all the

handsets ring for 30 seconds.

To stop paging, press INT-COM again.

(2) Handset: Press any key except or pick it up if it is placed on

the base unit or on the charger to answer.

(3) Handset: To end the intercom, press or place the handset

on the base unit or on the charger.

3. Paging the desired handset from the base unit

(1) Base unit: Press H1 (or H2 , H3 ) and the handset 1 (or 2,3) rings

for 30 seconds.

To stop paging, press H1 (or H2 , H3 ) again.

(2) Handset 1 (or 2, 3): Press any key except or pick it up if it is

placed on the base unit or on the charger to

answer.

(3) Handset 1 (or 2, 3): To end the intercom, press or place the

handset 1 (or 2,3) on the base unit or on the

charger.

17-EN

4. Paging the desired handset which number is over 3 from the base unit

For example: Page the handset No.5 through the handset No. 2.

(1) Base unit: Press INT-COM or H2 .

(2) Handset No. 2: Press any key except to answer.

(3) Handset No. 2: Press FUNC 5 to transfer the paging and the

handset No. 5 rings for 30 seconds (P. 28).

(4) Handset No. 5: Press any key except to answer.

If the handset No. 5 dosen’t answer, the paging will

be back to handset No.2 which will ring for 50

seconds (P. 28).

NOTE:

1. During paging from the base unit:

A confirmed melody sounds if the base unit receives the response

from handsets. If the melody does not sound, it means that:

(1) The handset is off.

(2) The handset is out of communication range.

(3) The handset’s ring mode is set at «4» (P. 29).

2. During the intercom:

(1) Intercom can only be ended by the handset.

(2) If a bell sounds, an incoming call has been received. To answer,

press and the intercom is ended.

G. Intercom during a call

During a call, press .

The call is put on hold and the hold music is heard on line.

A warning beep sounds every 30 seconds.

To resume the call, press .

To end the intercom and hang up, press .

18-EN

H. Call Waiting

You can answer another incoming call by using call waiting service.

During a call, press (FLASH) on handset if you hear a call waiting

tone.

The first call is put on hold and you can answer the second call.

To return to the first caller, press (FLASH) again.

Users should apply for the call waiting service from your local

telephone company.

Duration of «FLASH» is adjustable; see page 27 for reference.

I. Walkie-Talkie

The multi-handset system enables you to talk between the handsets in

Walkie-Talkie mode. The communication between the handsets is by way

of the base unit.

1. Walkie-Talkie between two handsets (ex: No. 5 paging No.8)

(1) Handset No. 5: Press FUNC 8 and the handset No. 8 rings

for 30 seconds.

If during a call, the call is put on hold.

If during the intercom, the intercom is ended.

To stop paging and resume the call, press .

To stop paging and resume the intercom, press

.

To stop paging and hang up, press .

(2) Handset No. 8: Press any key except to answer and enter

the Walkie-Talkie mode.

If the handset No. 8 doesn’t answer, during a

call or intercom, the paging will be back to the

handset No. 5 which will ring for 30 seconds.

(3) Handset: Press and hold PTT key to talk.

Release PTT key to listen.

(4) Handset: To end the Walkie-Talkie and resume the call, press .

To end the Walkie-Talkie and resume the intercom, press

.

To end the Walkie-Talkie and hang up, press .

19-EN

NOTE: During the Walkie-Talkie:

1. While in the Walkie-Talkie mode, all of H1, H2, H3 indicators

light up to show such function is working.

2. If holding a call, a warning beep sounds every 30 seconds.

3. If you keep to listening and not press PTT key to talk up to

4 minutes, warning beeps will sound. The handset will end

Walkie-Talkie function.

4. The voice volume is adjustable.

Base unit: To increase, press H1 .

To decrease, press H2 .

Handset: Press P/VOL .

5. Once an incoming call comes, the Walkie-Talkie mode will be

ended. You can press any key except to answer

incoming call.

J. Group call (Walkie-Talkie mode)

1. Walkie-Talkie among all the handsets

(ex: paging all the other handsets from the handset No. 2)

(1) Handset No. 2: Press FUNC and all the other handsets

ring for 30 seconds.

If during a call, the call is put on hold.

If during the intercom, the intercom is ended.

To stop paging and resume the call, press .

To stop paging and resume the intercom, press

.

To stop paging and hang up, press .

(2) Any other handset: Press any key except to answer and enter

the Walkie-Talkie mode.

If all the other handsets don’t answer, during

a call or intercom, the paging will back to the

handset No. 2 which will ring for 30 seconds.

(3) Handset: Press and hold PTT key to talk.

Release PTT key to listen.

20-EN

(4) Handset: To end the Walkie-Talkie and resume the call, press .

To end the Walkie-Talkie and resume the intercom, press

.

To end the Walkie-Talkie and hang up, press .

2. Walkie-Talkie among the base unit and all the handsets (paging all the

handsets from the base unit)

(1) Base unit: While in stand-by, press and hold INT-COM for 2

seconds and all the handsets ring for 30 seconds.

To stop paging, press INT-COM again.

(2) Any handset: Press any key except to answer and enter the

Walkie-Talkie mode.

(3) Base unit: Speak to the microphone.

Handset : Press and hold PTT key to talk.

Release PTT key to listen.

(4) Base unit: To end the Walkie-Talkie, press and hold INT-COM for

2 seconds.

Handset: To end the Walkie-Talkie and resume the call, press .

To end the Walkie-Talkie and resume the intercom, press

.

To end the Walkie-Talkie and hang up, press .

3. The user of third or more handsets can join the group call with

walkie-falkie mode.

Press or to join the Walkie-Talkie.

A confirmed tone » SO-SO-DO» sounds.

4. The base unit can join group call also.

To join the Walkie-Talkie, press INT-COM .

A confirmed tone » SO-SO-DO» sounds.

To release the Walkie-Talkie, press INT-COM again.

A release tone «DO-DO-SO» sounds.

5. If all of users in this mode don’t press PTT key to talk more than 4

minutes, warning beeps will sound and this mode will be ended.

21-EN

K. Lock Keypad of handset

This function enables you to lock the keypad of handset.

1. Enable key lock: press PTT key twice within 0.8 sec. The keylock LED

indicator will light up as well as keypad sound » bi «

disappears to confirm this process. (Handset will sound

» bi-bi-bi » once fail to complete above process)

2. Disable key lock: Press PTT key twice within 0.8 sec under the condition

of key lock.

3. During the process of key lock, all keypads will temporarily work once

handset receives paging to activate communication. Keypads will be

locked again once you finish communication.

22-EN

Advanced Operation

A. Adjusting the Ringer Volume

1. Base unit

The ringer volume of the base unit can only be adjusted in intercom

mode.

(1) Handset: Press and make sure that the intercom is established.

(2) Base unit: Press H3 to select the ringer volume.

There are 4 available levels, including mute, low level,

middle level, and high level. They are set in cycle.

Each time you press H3 , a bell sounds and the

ringer volume will be changed.

(3) Base unit: When finished, press INT-COM to store the volume level.

(4) Handset: Press to end the intercom.

choose a desired volume

INT

(handset)

Intercom

H3

(base unit) store

INT-COM

(base unit)

High level

(default)

Middle level

Mute

Low level

2. Handset

The ringer volume of the handset can only be adjusted in stand-by

mode.

(1) Press P/VOL to select the ringer volume.

There are 4 available levels, including mute (vibration), low level,

middle level, and high level. They are set in cycle. Each time

you press P/VOL , a bell sounds and the ringer volume will be

changed.

(2) When finished, press MEMO P/VOL to store the volume level.

choose a desired volume

P/VOL

(stand-by)

MEMO store

High level

(default)

Middle level

Low level

P/VOL

Mute

(Vibration)

23-EN

B. Adjusting the Voice Volume

1. Base unit

The voice volume of the base unit can only be adjusted in intercom

mode.

(1) Handset: Press and make sure that the intercom is established.

(2) Base unit: There are 8 available levels .

To increase, press H1 .

To decrease, press H2 .

(3) Base unit: When finished, press INT-COM to store the volume level.

(4) Handset: Press to end the intercom.

Intercom

(handset)

(base unit)

Choose a

H1 up level desired volume

H2

(base unit) lower level store

INT-COM

(base unit)

8th level

7th level

6th level

5th level (default)

4th level

3rd level

2nd level

1st level up volume

2. Handset

(1) Press P/VOL while in use to adjust the voice volume.

There are 6 available levels being set in cycle. Each time

you press P/VOL , the voice volume will be changed.

(2) Press MEMO P/VOL to store the volume level.

or

2nd level choose a desired volume

P/VOL

(in use)

3rdlev el

(default)

4th level

MEMO store

P/VOL

1st level

5th level

6th level

24-EN

C. Selecting the Voice Mode

Press FUNC P/VOL ,while in use, to select the voice mode.

There are 4 available modes being set in cycle. Each time you

press FUNC P/VOL the voice mode will be changed .

or FUNC P/VOL

Normal

(Power on default)

Voice mutationB return to normal in stand-by

Voice mutation A return to normal in stand-by

Scrambler

Voice mode SCRAMBLER indicator

Normal light off

Scrambler light up

Voice mutation A slow blink

Voice mutation B fast blink

D. Transferring a Call among Handsets

The multi-handset system allows you to transfer a call among the

handsets.

1. Transferring a call from the handset No. 5 to the handset No. 8

(1) Handset No. 5: During a call, press FUNC 8 .

The call is put on hold.

The handset No. 8 rings for 30 seconds (P. 28).

To stop transferring, press any key except .

(2) Handset No. 8: Press any key except or pick it up if is placed

on the base unit or on the charger to answer.

25-EN

2. Transferring a call from the handset No.5 to any other handset

(1) Handset No. 5 : During a call, press FUNC .

The call is put on hold.

All the handsets except No. 5 ring for 30

seconds (P. 28)

To stop transferring, press any key except .

(2) Any other handset: Press any key except or pick it up if it is

placed on the base unit or on the charger to

answer.

E. Changing the Channel during a Conversation

To change channel is available while you get interference during a

conversation.

Handset: Press FUNC # during a conversation.

F. Display the battery status

The LED array of the handset can display the capacity of the battery.

Handset: Press REDIAL while in stand-by mode.

LOW FULL

The more light-up LED bar, the more capacity battery is.

26-EN

Setting Features

A. Setting the Base Unit

The parameters of base unit are set through the handset. First, press

on handset and make sure that the intercom is established.

1. Setting PAUSE duration

0 1 N MEMO

(handset) (N: 1~4) store

N : PAUSE duration

1 : 2 seconds 3 : 4 seconds

2 : 3 seconds 4 : 6 seconds (default)

2 Setting dialling mode

0 2 N MEMO

(handset) (N: 1~8) store

N : Speed of pulse dialling mode

1 : 20 PPS 40/60

2 : 20 PPS 33/67

3 : 10 PPS 40/60

4 : 10 PPS 33/67 (default)

N : Inter-digital-time of DTMF dialling mode

5 : 140 ms

6 : 200 ms

7 : 70 ms

8 : 100 ms (default)

3 Setting flash duration

0 3 N MEMO

(handset) (N: 1~9) store

N: flash duration

1 : 100 ms 4 : 400 ms 7 : 700 ms

2 : 200 ms 5 : 500 ms 8 : 800 ms

3 : 300 ms 6 : 600 ms (default) 9 : 900 ms

27-EN

4. Setting max. amount of handsets registered to one base unit (up to

15 ). The amount of handsets registered

to one base must be not more than this parameter.

0 4 N MEMO

(handset) (N: 1~05) store

N: Max. amount of handsets

1 : 1 handset(default) 6 : 6 handsets 0 1 : 11 handsets

2 : 2 handsets 7 : 7 handsets 0 2 : 12 handsets

3 : 3 handsets 8 : 8 handsets 0 3 : 13 handsets

4 : 4 handsets 9 : 9 handsets 0 4 : 14 handsets

5 : 5 handsets 0 0 : 10 handsets 0 5 : 15 handsets

5. Setting transferring waiting time

When the handset transfers a call to another handset, and if the

designated handset doesn’t answer within period of transferring

waiting time which has been set, then it will stop paging and ring

back the original handset.

0 5 N MEMO

(handset) (N: 1~9) store

N: Transferring waiting time

1 : 15 sec. 4 : 30 sec. (default) 7 : 45 sec.

2 : 20 sec. 5 : 35 sec. 8 : 50 sec.

3 : 25 sec. 6 : 40 sec. 9 : 55 sec.

6 . Setting call-back waiting time

Continue above item, if the handset doesn’t answer the call within

period of call-back waiting time which has been set, then the call

will be ended.

0 6 N MEMO

(handset) (N: 1~9) store

N: Call-back waiting time

1 : 15 seconds 4 : 30 seconds 7 : 45 seconds

2 : 20 seconds 5 : 35 seconds 8 : 50 seconds (default)

3 : 25 seconds 6 : 40 seconds 9 : 55 seconds

28-EN

B. Setting the Handset

When the setting is finished, a confirmation tone » bi-bi» sounds.

When failed, an error tone «bi-bi-bi» sounds. If misdialed, press to

end setting, then restart.

1. Change Handset’s ID (in stand-by mode)

To change handset’s ID, please make sure that each handset has

an individual ID. It is not allowed that two handsets have the same ID

and the ID number is more than the amount of handsets registered

to one base unit. Once above setting is being against, the operation through base unit will be failed.

FUNC 0 1 N MEMO

(N: 1~05) store

N : ID

1 : 1 4 :4 7 :7 0 0 :00 0 3 : 03

2 : 2 5 :5 8 :8 0 1 :01 0 4 : 04

3 : 3 6 :6 9 :9 0 2 :02 0 5 : 05

2. Setting ring mode for each handset (in stand-by mode)

FUNC 0 2 N MEMO

(N: 1~5) store

N : Ring mode

1 : ring (default)

2 : only ring 2 seconds

3 : silence

4 : make calls only, but can not answer calls

Under this mode the battery stand-by time is up to about

200 hours.

5 : answer calls only, but can not make calls

29-EN

3. Setting stand-by time for each handset (in stand-by mode)

The longer stand-by time is set resulting in the longer response time

of an incoming call.

FUNC 0 3 N MEMO

(N: 1~9) store

N: Stand-by time

1 : 58 hours 4 : 80 hours 7 : 92 hours

2 : 66 hours 5 : 85 hours (default) 8 : 95 hours

3 : 74 hours 6 : 89 hours 9 : 98 hours

30-EN

Registering handset for multi-handset system

Your handset(s), if purchased with base unit, is pre-registered at the factory

A. Handset Registration

When purchasing a new handset, be sure to follow below steps for

registering it.

1. The new handset (non-registered)

(1) Install the battery (P. 9)

(2) Check the handset whether it is a new one or not by pressing

to turn it on.

If the handset can not be turned on, it is a non-registered one.

Do the following steps 2~3.

If the handset can be turned on, it is the one which has registered

to another base unit already. Please do the procedure B (P. 32) to

de-register it first, then do the following steps 2~3.

2. Base unit

(1) Unplug the AC adaptor.

(2) Press and hold on H1 .

(3) Plug in the AC adaptor.

(4) After 3 seconds, a tone «DO-SO-MI-SO…» sounds for 10 seconds.

(5) Release H1 .

3. The new handset

(1) During the tone «DO-SO-MI-SO…» sounds, place the new handset

on the base unit with facing up.

(2) A tone » DO-SO-MI-SO…» sounds from the handset.

(3) The base unit registers the new handset automatically.

When successfully registered, a confirmation tone «DO-MI-SO-DO»

sounds. The amount of handsets used in the system is added by

one automatically.

The ID of new handset is set in sequence and as same as the

amount of handsets used in the system.

31-EN

B. De-registering handset

When a registered handset code needs to be de-registered, follow below steps.

1. If the handset is power on, press and hold about 3 seconds to

turn it off.

2. Press and hold MEMO and about 3 seconds, a tone

» bi-bi» sounds.

C. Checking the handset’s ID number

While in stand-by mode, the LED array indicates the ID of handset.

LED status Handset number LED status Handset number

D. Checking the parameters

While in multi-handset system, please check the parameters set in the

handsets and the base unit.

1. Each handset has an individual ID. It is not allowed that two handsets

have the same ID.

2. The max. handset’s ID number is suggested to be as same as the

parameter «max amount of handsets ID registered to one base».

(1) To change the ID of handset, refer to P. 29.

(2) To reset the parameter «max. amount of handsets registered to one

base», refer to P. 28.

32-EN

Troubleshootings

If you have difficulty operating on your phone, the below suggestions should solve the problem. If you still have difficulty after trying these suggestions, please call your local SENAO service station for further assistance.

A. The Phone does not work……

1. Check the installation (P. 8~P.14)

2. Make sure the power cord is plugged in.

3 . Is the handset battery fully charged?

4. Is the handset power on?

B. The handset does not ring……

1. Make sure the telephone line cord is plugged firmly into the base unit

and the telephone jack.

2. You may be too far from the base unit.

3. Check the ring mode for the handset (P. 29).

C. Interference, static, sound cuts in/out, fades……

1. Is the telescopic antennas of the base unit and the handset fully

extended?

2. Move closer to the base unit.

3. Press FUNC # to change the channel.

D. How to build multi-base units system?

Send all the base units and the handsets to your local SENAO service

station for setting this system.

33-EN

Specifications

Item

Transmitter

Frequency

Output power

Spurious emission

Current consumption

Stand-by

Talk

Receiver

Frequency

Sensitivity at 12 dB SINAD

(CCITT)

Adjacent channel rejection

Spurious response

Power source

Dimension

Weight

Base unit

388 MHz

1 W

55 dBc

100 mA

600 mA

262MHz

-122dBm

50 dBc

55 dBc

AC 110V/60 Hz

AC 220V/50 Hz

DC 12V

L x W x H (m/m)

195x 145x 51

500g

Handset

262 MHz

350 m W

55 dBc

7~12 mA

350 mA

388MHz

-122dBm

50 dBc

55 dBc

4.8V/750 mAh

Ni-Mh Battery

L x W x H (m/m)

150x 53x 32

210g

34-EN

Important Safety Instructions

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

1.

Read and understand all instructions.

2.

Follow all warnings and instructions marked on the product.

3.

Unplug this product from the wall outlet before cleaning. Do not use

liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

4.

Do not use this product near water, for example, near a bath tub, wash

bowl, kitchen sink, or laundry tub, in wet basement, or near a swimming

pool.

5.

Do not place this product on an unstable cart, stand, or table. The

product may fall, causing serious damage to the product.

6.

Slots and openings in the cabinet and back or bottom are provided for

ventilation. To protect it from overheating, these openings must not be

blocked or covered. The opening should never be blocked by placing

the product on the bed, sofa, rug, or other similar surface. This product

should never be placed near or over a radiator or heat register, ro in a

built-in installation unless proper ventilation is provided.

7.

Use only the power source indicated on the marking label. If you are not

sure of the type of power supply to your home, consult your dealer or

local power company.

8.

Do not allow anything to reset on the power cord. Do not locate this

product where the cord will be damaged by persons walking on it.

9.

Do not overload wall outlets and extension cords as this can result in the

risk of fire or electric shock.

35-EN

10.

Never push objects of any kind into this product through cabinet slots as

they may touch dangerous voltage points or short out parts that could

result in a risk of fire or electric shock. Never spill liquid of any kind on the

product.

11.

To reduce the risk of electric shock, do not disassemble this product.

Take it to an authorized service center when service or repair work is

required. Opening or removing covers may expose you to dangerous

voltages or other risk. Incorrect reassembly can cause electric shock

when the appliance is subsequently used.

12.

unplug this product from the wall outlet and refer servicing to an

authorized service center when the following conditions occur:

A. When the power supply cord or plug is damaged or frayed.

B. If liquid has been spilled into the product.

C. If the product has been exposed to rain or water.

D. If the product does not work normally by following operating

instructions. Adjust only those controls that are covered by the

operating instructions because improper adjustment of other controls

may result in damage and will often require extensive work by a

qualified technician to restore the product to normal operation.

E. If the product has been dropped or the cabinet has been damaged.

F. If the product exhibits a distinct change in performance.

13.

Avoid using a telephone (other than a cordless type) during an electric

storm. There may be remote risk of electric shock from lightning.

14.

Keep the outdoor antenna cable away from sources of high-voltage to

avoid electric shock when installing the outdoor antenna for this product.

15.

Do not use the telephone to report a gas leak in the vicinity of the leak.

36-EN

P/N: 670901183000

SENAO INTERNATIONAL CO., LTD.

http://www.senao.com

Specifications: 2404/2404373-sn258_plus.pdf file (01 Feb 2023)

Accompanying Data:

SENAO SN-258 PLUS Cordless Telephone PDF Instruction Manual (Updated: Wednesday 1st of February 2023 11:59:00 PM)

Rating: 4.1 (rated by 59 users)

Compatible devices: ARC 3, EXI6960, 1210, SN-358 SKYPE, DE 331, FreeStyl 2, SI-7800H, EP801.

Recommended Documentation:

Text Version of Instruction Manual

(Ocr-Read Summary of Contents of some pages of the SENAO SN-258 PLUS Document (Main Content), UPD: 01 February 2023)

• SENAO SN-258 PLUS User Manual

• SENAO SN-258 PLUS User Guide

• SENAO SN-258 PLUS PDF Manual

• SENAO SN-258 PLUS Owner’s Manuals

Recommended: HVW18 Service, SB-TC50, OWR-150

• 

• 

• 

• 

• 

• 

• 

Popular Right Now:

Operating Impressions, Questions and Answers: